Used Wind Generators & Equipment
Click on pictures for a larger viewSome items on this page are shown for historical and informational purposes. All items are sold as is.
|
Jacobs, Parris-Dunn, Wincharger, WinPower,
WhirlWind. Towers. |
E44 Enertech Service manual and Installation manual
$45 21/5 Enertech Service manual and Installation manual $45 4000 Enertech Owners manual $25 1800 Enertech Owners manual $25 1500 Enertech Owners manual $20 |
| Owner’s Manuals for most wind generators are $25 plus shipping |
|
For Sale
Jacobs Model 45 1800 watt, 32 volt DC. Located at Tribune, KS. |
 |
|
|
 |
|
Parris
Dunn
|
 |
 |
 |
||
 |
|||||
 |
 |
 |
|||
 |
|||||
|
New Aermotor Windmills and Towers |
|
New Aermotor Towers
Towers for 6' or 8' Wheel 21' is 445 lbs $3205, 27' is 500 lbs $3713, 33' is 660 lbs $4406, 40' is 775 lbs $5150, 47' is 930 lbs $6040. Towers for 10' Wheel 21' is 509 lbs $3805, 27' is 539 lbs $4710, 33' is 730 lbs $4955, 40' is 860 lbs $5856, 47' is 995 lbs $6864. Towers for 12, Wheel 27' is 780 lbs $5589, 33' is 963 lbs $5825, 40' is 1140 lbs $6831, 47' is 1440 lbs $7912. Towers for 14' Wheel 27' is 900 lbs $5680, 33' is 1090 lbs $6546, 40' is 1300 lbs $7117, 47' is 1590 lbs $9812. Towers for 16' Wheel 33' is 1420 lbs $8688, 40' is 1780 lbs $9607, 47' is 2210 lbs $11,737 |
|
New Aermotor Windmills
6' is 200 lbs $3720, 8' is 350 lbs $3857, 10' is 640 lbs $5627, 12' is 1090 lbs $9471, 14' is 1735 lbs $13,650, 16' is 2380 lbs $17,880. |
|
Used Towers & Windmills for sale |
||
| 30' Windmill Tower, 4-leg galvanized angle iron, 10' base section, 20' upper section $1200 Special $790 | ||
| 55' very
heavy 4-leg galvanized angle iron. Made with 4"x4"x5/16" angle iron legs with
2"x2"x3/16" cross braces. Climbing bolts make a ladder on one leg of the
tower. 3 sections: Bottom
section is about 15' long, about 49" wide at bottom, 36" at top. Middle
section is 25.5' long and 18" wide at top. Top section is 14.5" long and 8"
wide at top. This tower was originally used for electrical
distribution lines just a few blocks North of the Kansas Capitol building in
Topeka. The tower could also be made taller by adding to the top with angle
iron or pipe to attach a wind generator. $7500
Special $1890 Extra tower section is 10' 11" long, 45" wide at bottom and 36" wide at top. $1200 Sold |
 |
|
| 100' very heavy 4-leg galvanized angle iron, 4-25' sections, 3"x3"x1/4", 2.5"x2.5"x1/4", 2"x2"x3/16". Top is 29" x 29" $11,000 Special $2700 | ||
| 10' sections, Rohn 25G 3-leg galvanized 45 lbs, for guyed towers or short self-supporting. $190, Top sections $250 | ||
|
Bergey 10 KW & 100' Tower |
|
A 10 KW Bergey with 100' Rohn Self Supporting Tower. Needs inverter and furling cable repaired. Located in Southwest Kansas near Johnson. |
|
WhirlWind |
||||||
|
|
|
WhirlWind 2 KW, 3 KW, 4 KW, 10 KW 3000 watt, 32 volt or 120 volt, 14' rotor, 230 lbs Not available, shown for historical and informational purposes. |
 |
 |
 |
 |
| WhirlWind 4000 watt, 32 volt, 16' blade diameter on tower behind house. Two electric pickups with tilting bed. | WhirlWind 3000 with control box. 1970 Porsche 914 | |||||
 |
 |
 |
 |
 |
 |
| Two WhirlWind 3000 on 60 foot towers. | 3000 watt | 60" Tower |
2" Ice Storm, 4 KW |
Model A 120 volt DC |
|
|
7.5' WhirlWind Blade, Good
wood half blade for the 15' blade used on 4 KW and similar sized wind
generators. There is enough wood to make the blade 8' long. Shipping and
crating is extra. $300
8' WhirlWind Blade, Good
wood half blade for the 16' blade used on most 4 KW WhirlWind and similar
sized wind generators, Shipping and crating
is extra. $300 |
||||||||||||||||||||
|
WinPower |
|||||||||||||||||||||
|
|
WinPower by Wind Power Co. Newton, Iowa 1800 watt, 32 volt, 12' diameter, down wind design-blades act as a tail. Band brake for shut off. Blades feather in high winds. Flyball Governor activates with RPM and wind pressure against the blades. These are heavy built units and weigh about 350 pounds. 2 blades sets available. Tower Cap Made to fit 3-leg or 4-leg tower with turn table bearings, Slip Rings, Brush Card. Brush Card has Generator positive, negative and field connections. |
||||||||||||||||||||
 |
 |
|
 |
|
 |
 Brush Card $195 |
 |
 |
|||||||||||||
|
set 1 $300 |
|||||||||||||||||||||
 |
 |
 |
|||||||||||||||||||
|
set 2 $300 |
|||||||||||||||||||||
|
|
|
 |
 |
WinPower 1800 watt, 32 volt DC Control Panel Has cutout relay, generator fuse holder, field fuse
holder, 50-0-50 amp meter, connection terminals for Generator positive and
negative, field, Battery positive and negative. |
|||||||||||||||||
|
WinCharger |
|||||||||||||||||||||
|
Jim Davis' pictures of his beautifully restored Wincharger Streamliner. |
 |
 |
 |
 |
|||||||||||||||||
|
11' Blade
Sold Blade Length 10' 11-3/4", 4 Bolt hub diagonal bolt hole spacing 3-3/4" |
|
||||||||||||||||||||
 |
|
 |
 |
 |
 |
 |
|||||||||||||||
| Cutout Relay, Amp Meter and Voltage Control Relay $199 | Cutout Relay and Amp Meter Sold | Over Charge Regulator Sold | |||||||||||||||||||
| 1500 watt Gearbox $99 |
 |
 |
 |
||||||||||||||||||
| Special - 3 governors and 2 covers for $199 | |||||||||||||||||||||
 |
 |
Disassembled | Governor Cover $55 |
 |
 |
 |
| 4-Blade Governor $295 | 4-Blade Governor $250 | 4-Blade Governor $50 | Governor Cover $35 |
 |
 |
 |
|
6 volt,
100 watt WinChargers |
Frame Halves 2
are needed for one wind generator. These hold the generator, tail boom and tower yaw tube. $3 each |
 |
 |
|
Jacobs 32 volt |
||||||||
|
|
This
Sunset picture was taken 1/2 mile away from the Jacobs wind generator
located at Kansas Wind Power. Tower is 75 feet high. The blade diameter is
13.5 feet. The very heavy, slow speed, direct drive generator is rated:
32-40 volts DC, 60 amps. Unit weighs about 550 lbs. © 1978 Kansas Wind Power |
1800 watt, 32 volt Field and Armature with bent shaft $45 |
|
|||||
|
|
||||||||
|
Control box with
voltmeter |
 |
|
 |
 |
 |
Flyball Governor $1500 Sold |
||
|
|
||||||||
|
|
ParrisDunn Sold 1200 watt, 32 volt, 11' rotor Entertaining - This is one of our favorite wind generators to watch in action. The entire rotor and generator tip back to govern in higher winds. The tail assembly is over 8 feet long. Partially rebuilt in 1975, ran for 1-2 years then put in storage. |
|
|
 |
Enertech 1500/1800
3 blades, 13' diameter,
downwind rotor, 120 VAC
Enertech parts, control boards and repairs are available from: |